Fu Chip problem

[epowers777]

I am having an issue with the chip. I have the switch hanging over the steering wheel cause I havent installed it yet. My truck shut off like 5 times today. Im guessing that Im not haveing good contact with the computer. If you bump the wire my truck shuts off. But is seems the chip doesnt move at all.:confused: I think its the switch going to the php chip any ideas?

Also I tried the smoke show today and no smoke and the engine sounded horrible. Like the injectors are overloading? Do they do that? Can someone explain to me how the injectors work? So the only tunes that work good for me is the 2 economy ones. I tried the towing one today while getting on the freeway and it sound like the smoke show and the 100hp overloading sound.

Last question after my truck sits for a few days when I go start it it sounds like its missing (like a lopy cam). After awhile it goes away. I thought it was a leaky fuel bowl. Any ideas on that?

Thanks for your help.

[cleatus12r]

I've got a message to Bill. Unfortunately, I know he's gone to Utah right now and won't be able to help much for the next week. Definitely keep driving on the tunes that you feel comfortable with and hopefully he can get you squared away.

[epowers777]

The bottom question has nothing to do with the chip just wondering if I could get your help on that one.


Im going to pull the computer out and clean the connections better. How clean should I go?

[cleatus12r]

Cleaning the contacts:

http://forum.gopowerhungry.com/phoenix-switch-fly-chip/1613-cleaning-j3-connector-powertrain-control-module.html

As far as the "lopey cam" sound, is it a situation that causes a "ruh-ruh-ruh-ruh" sound (say "ruh" just a tad faster than once a second)?
If so, it's almost a normal characteristic when it's below 30 degrees outside and if you're using 15/40 oil. It should only last a few seconds though. If it's a rhythmic miss, check the exhaust while it's doing it....any white smoke that smells like raw fuel?

[soutthpaw]

which tunes did you get on your chip??? do you have any mods beside the chip? Definitely clean your contacts again...

[epowers777]

MMMM maybe thats it Im running a delo 400 20 40w industrial oil. It sounds like it misses and then itll go away after like a minute. I heard you can pull out the oil line and clean it for the injectors. Do you have any info on it? Other guys at my work have been running this oil on there powerstrokes and have had no issue.

I think I got the regular tunes for stock truck. Bill was trying to figure out if I had a pre or late 99. He asked me if I had a heater on my truck I told him Yes 2 large wires going to a probe near the turbo valve red line. Also I have a refurbished computer,

i have and intake and exhaust. I think the exhaust is 4 in and then a hollow muffler with a 6 inch tip.

[epowers777]

1999 or 99.5 - Page 2 - Powerstroke Nation (http://www.powerstrokenation.com/forums/showthread.php?p=772561)
Scroll down my engine looks exactly like that. It says its a late 99 Bill gave me the early 99 tunes. I will take a pic of engine to verify.

[Robert6401]

Have you tried cleaning the contacts again and just generally making sure the chip is seated well? When I first installed mine, it would shut off intermittently. The contacts were plenty clean, but the chip just wasn't seated well.

[epowers777]

I cleaned my connectors and found out it was a bad connection. The truck does not kick off. My starting issue seems gone the fuel bowl plug was unplugged. I plugged it in and it hasnt gone raw raw yet.
Im am still getting that injector soung with tow mode and smoke show and 100hp performance. can bill send me new tunes since we found out I have a late 99?

[cleatus12r]

Of course! All he needs to do is update the tunes on his server for you to download. You'll probably have to wait until he gets back on Tuesday or Wednesday. He's going to be super busy though so just cruise around on your other tunes until then!

[epowers777]

I cant waite!!

[soutthpaw]

I highly recommend going with a full synthetic engine oil like Rotella 5w40 synthetic... its available for $19.50 a gallon at Wally mart and they also sell the Motorcraft FL1995 filter for $10. If you are in a cold environment the syn oil will make a big difference in cold starting and warm up

[epowers777]

Hi I was wondering if Bill was in today. I would like to get the late 99 tunes pls.:) I told my chiropractor about you so hopefully he buys one!!

[cleatus12r]

Hi I was wondering if Bill was in today. I would like to get the late 99 tunes pls.:) I told my chiropractor about you so hopefully he buys one!!


If you make a new post in the General Support Requests forum, you may get a quicker response.

[strokindually]

just for my understanding whats the differance between ca and federal tunes?

[cleatus12r]

Mostly glow plug control. CA trucks had an actual module that controls and monitors each glow plug whereas 49 state trucks have a simple relay that just turns them all on and off.

[epowers777]

Here is the Vin 1FTWW33F3XEE84687

This is the full number printed on the board itself.
pwb6938/dpc-4xx/xc3f-ba and other side g-030954

can I us the obd2 scanner the get the hex code?

[Jeremy]

This is all thats in Oasis for his truck, its too old to get anything else.

VIN: 1FTWW33F3XEE84687
Vehicle Data: 2E1F 18D8 FF3C



Module Information Found


PCM Module
PCM 1 FFFF FFFF FF0C
PCM 2 FFFF FFFF FF0D
PCM 3 FFFF FFFF FF0E
PCM 4 FFFF FFFF FF0F
PCM 5 FFFF FFFF FF10
PCM 6 FFFF FFFF FF11
PCM 7 FFFF FFFF FF12
PCM 8 FFFF FFFF FF13
PCM 9 FFFF FFFF FF14


BCE Modules
58-01 FFFF FFFF FF54


End of As Built information
FCXWS446

[cleatus12r]

The thing that gets me is the XC3F-BA.

According to Bill's literature, there is no suffix of "BA" for the prefix of "XC3F". Just "BB-BG" which translate into NVK0-NVK5.

[epowers777]

Well the scanner did not work. It would link and when you go to vehicle info it says this is not supported. it says no codes stored and like2 monitors were working. When i pulled the carfax the the truck was a program car.

[epowers777]

I still wanna figure this out any other help?

[epowers777]

Im still waiting for help on this.

[cleatus12r]

Where are you located?

I can send you a PCM that will allow you to drive your truck while you send your PCM to PHP so Bill can know EXACTLY what the calibration code is.

Up to this point, there is nothing that anyone can do since your PCM calibration code is unknown.