Power Hungry Performance Forum  

Go Back   Power Hungry Performance Forum > Power Hungry Performance Product Information > Gryphon Programmer (Disabled)

Gryphon Programmer (Disabled)
Edge Product has discontinued the Edge Evolution 2, but we still provide support and tuning for it.

If you have a question or comment relating the Gryphon (or Evolution) programmer, post it here.


 
 
Thread Tools Display Modes
  #1  
Old Wed, April 29th, 2009, 07:22 PM
TA2Dsailor TA2Dsailor is offline
Redbull Junkie
 
Join Date: Feb 2009
Location: OKC, OK
Posts: 34
TA2Dsailor is on a distinguished road
checksum failure

I just recieved my gryphon yesterday and hooked it up. I tried loading the 93 performance tune. It went through some steps then at the end it said checksum failed and had my hex code. After this the truck would not start.I unplugged it and it started and ran fine. I tried all three tunes with the same results. Any ideas? Am I doing something wrong?

Anthony
__________________
  #2  
Old Wed, April 29th, 2009, 08:10 PM
88Racing's Avatar
88Racing 88Racing is offline
SENIOR MODERATOR
 
Join Date: Feb 2009
Location: Somewhere ....
Posts: 4,241
88Racing is a glorious beacon of light88Racing is a glorious beacon of light88Racing is a glorious beacon of light88Racing is a glorious beacon of light88Racing is a glorious beacon of light88Racing is a glorious beacon of light
Default

Did you update it on pegasus before it went in the truck?
Or did you plug it in right out of the box?

Key on in run position but motor not running.

I'll see if the mad doctor or groovy chick can help. Maybe Jack knows something about this.

Lars
__________________
SENIOR MODERATOR--PTLA

God doesn't have a Facebook but he's my friend.
God doesn't have a twitter, but I follow him.
  #3  
Old Wed, April 29th, 2009, 08:26 PM
TA2Dsailor TA2Dsailor is offline
Redbull Junkie
 
Join Date: Feb 2009
Location: OKC, OK
Posts: 34
TA2Dsailor is on a distinguished road
Default

Plugged it in straight out of the box. I'll try to update it and try it again.

turned key on set it to 93 performance key off key on started to load. check sum failure tried to start and nothing message poped up on odometer CHECK GUAGES

I pm'd Jack and Bill already. Just wanted to see if anyone else had this problem and knew how to fix it.

Anthony
__________________
  #4  
Old Wed, April 29th, 2009, 08:35 PM
JWBFX4 JWBFX4 is offline
Triple Whopper with Cheese
 
Join Date: Feb 2009
Location: Tuscaloosa,AL
Posts: 804
JWBFX4 is on a distinguished road
Default

Quote:
Originally Posted by TA2Dsailor View Post
Plugged it in straight out of the box. I'll try to update it and try it again.

turned key on set it to 93 performance key off key on started to load. check sum failure tried to start and nothing message poped up on odometer CHECK GUAGES

I pm'd Jack and Bill already. Just wanted to see if anyone else had this problem and knew how to fix it.

Anthony


Well it should be updated if you just bought this...unless it was used. Because I am pretty sure they said they update them with the latest firmware before shipping out.

Now to the part in bold....did you make sure to turn your key to the on position(without truck running) before you plugged the gryphon up to the cable?...And I found that the check gauges happens everytime I go to program my truck especially if it has done been cranked...something about the programming overiding the sensors at the time?? I think that was the explanation.
__________________
Flowmaster 40, PHP Gryphon, AS 2" kit
Thanks http://screen-fx.net for the sig.
  #5  
Old Wed, April 29th, 2009, 08:45 PM
TA2Dsailor TA2Dsailor is offline
Redbull Junkie
 
Join Date: Feb 2009
Location: OKC, OK
Posts: 34
TA2Dsailor is on a distinguished road
Default

Quote:
Originally Posted by JWBFX4 View Post
Now to the part in bold....did you make sure to turn your key to the on position(without truck running) before you plugged the gryphon up to the cable?...And I found that the check gauges happens everytime I go to program my truck especially if it has done been cranked...something about the programming overiding the sensors at the time?? I think that was the explanation.
Yes the key was in the on position without truck running. The first time I tried it the truck had been sitting for about 9 hours. Also tried right after driving with same results.
__________________
  #6  
Old Wed, April 29th, 2009, 08:52 PM
88Racing's Avatar
88Racing 88Racing is offline
SENIOR MODERATOR
 
Join Date: Feb 2009
Location: Somewhere ....
Posts: 4,241
88Racing is a glorious beacon of light88Racing is a glorious beacon of light88Racing is a glorious beacon of light88Racing is a glorious beacon of light88Racing is a glorious beacon of light88Racing is a glorious beacon of light
Default

Tell you what. Run the truck for 5-10 minutes with nothing on(no lights or accessories). Wait 5 minutes. Try going through the steps again. You might be having a voltage issue. Even try it with the door closed.

Hope this helps.

Lars
__________________
SENIOR MODERATOR--PTLA

God doesn't have a Facebook but he's my friend.
God doesn't have a twitter, but I follow him.
  #7  
Old Wed, April 29th, 2009, 08:55 PM
JWBFX4 JWBFX4 is offline
Triple Whopper with Cheese
 
Join Date: Feb 2009
Location: Tuscaloosa,AL
Posts: 804
JWBFX4 is on a distinguished road
Default

http://dygytalworld.ehost-services13...ecksum+failure

I do remember seeing this awhile back...I dont know that it has anything to do with you case, but I figured I would post it up.
__________________
Flowmaster 40, PHP Gryphon, AS 2" kit
Thanks http://screen-fx.net for the sig.
  #8  
Old Wed, April 29th, 2009, 09:03 PM
88Racing's Avatar
88Racing 88Racing is offline
SENIOR MODERATOR
 
Join Date: Feb 2009
Location: Somewhere ....
Posts: 4,241
88Racing is a glorious beacon of light88Racing is a glorious beacon of light88Racing is a glorious beacon of light88Racing is a glorious beacon of light88Racing is a glorious beacon of light88Racing is a glorious beacon of light
Default

Quote:
Originally Posted by JWBFX4 View Post
http://dygytalworld.ehost-services13...ecksum+failure

I do remember seeing this awhile back...I dont know that it has anything to do with you case, but I figured I would post it up.
Good one! JWBFX4
I will have to file that one!

Better start to contact Bill!

Lars
__________________
SENIOR MODERATOR--PTLA

God doesn't have a Facebook but he's my friend.
God doesn't have a twitter, but I follow him.
  #9  
Old Wed, April 29th, 2009, 09:10 PM
JWBFX4 JWBFX4 is offline
Triple Whopper with Cheese
 
Join Date: Feb 2009
Location: Tuscaloosa,AL
Posts: 804
JWBFX4 is on a distinguished road
Default

Quote:
Originally Posted by 88Racing View Post
Good one! JWBFX4
I will have to file that one!

Better start to contact Bill!

Lars

Yea I believe this one, might be up to Bill.

Hope you get up and running with it soon though
__________________
Flowmaster 40, PHP Gryphon, AS 2" kit
Thanks http://screen-fx.net for the sig.
  #10  
Old Wed, April 29th, 2009, 09:25 PM
TA2Dsailor TA2Dsailor is offline
Redbull Junkie
 
Join Date: Feb 2009
Location: OKC, OK
Posts: 34
TA2Dsailor is on a distinguished road
Default

hmm hopefully thats the case. Thanks JWBFX4.
__________________
 


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:55 PM.


All Contents Copyright 2008-2024, Power Hungry Performance