Search:

Type: Posts; User: cleatus12r

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    34
    Views
    5,985

    Re: Winter project in the works.

    Going to the machine shop tomorrow.

    181
  2. Replies
    2
    Views
    105

    Re: Exhaust Backpressure vs Boost

    I wish I had a definite answer for you concerning the pressure differential (Delta) between drive pressure and boost pressure but it all comes down to how robust the materials are and the build...
  3. Replies
    34
    Views
    5,985

    Re: Winter project in the works.

    Miss and white smoke at an idle and low load. Ran fine under boost when there was enough dynamic compression to ignite the fuel. Tons of blowby into the crankcase (diesel fuel smell to the "puffs"...
  4. Replies
    34
    Views
    5,985

    Re: Winter project in the works.

    I tore down the current donor engine today. It sucks that it only has 154K and a broken #8 top ring.....but that's how I ended up with it for a trade on labor costs for a replacement 6 years ago.
    ...
  5. Replies
    34
    Views
    5,985

    Re: Winter project in the works.

    179Got steering?
  6. Replies
    34
    Views
    5,985

    Re: Winter project in the works.

    I am waiting on installing some steering shaft parts that should be here tomorrow before pulling the engine out for the last time. I have probably gone in and out with it 12-15 times. The steering...
  7. Replies
    34
    Views
    5,985

    Re: Winter project in the works.

    Getting closer.

    Here's a short video showing progress up to yesterday.
    https://youtu.be/HF02zX2ay00
  8. Thread: LOCK UP

    by cleatus12r
    Replies
    5
    Views
    160

    Re: LOCK UP

    I wouldn't say that there's little need for it. Some driving conditions arise when the "mod" would be quite handy because no matter how much time is spent writing a calibration that will do all of...
  9. Thread: LOCK UP

    by cleatus12r
    Replies
    5
    Views
    160

    Re: LOCK UP

    You shouldn't have any problems at all unless something goes wrong with the torque converter control. In other words, you won't experience any more of an issue using something like this whether...
  10. Replies
    34
    Views
    5,985

    Re: Winter project in the works.

    I made a little progress this weekend.

    Engine sitting there supported on the frame and by a jack under the rear of the pan (to keep it from tipping backward only).
    177


    Plenty of room for...
  11. Replies
    34
    Views
    5,985

    Re: Winter project in the works.

    The first year of marriage took a toll on "me-time" and since the shop is now technically a "heated shop" as of October, I will be able to blast through work at home.
  12. Replies
    34
    Views
    5,985

    Re: Winter project in the works.

    174175

    Holy cow. More than a year late starting this again. I drove it all summer with the lift and it turns out that I really like it this way.

    I finally put it in the shop and started...
  13. Re: Hydra Chip - Hydra Flash Software Issue Need Help

    You'll have to call PHP. There are some driver/administration permissions that are a bit, well, RETARDED in Windows 8 if I'm not mistaken.

    Anything past Windows XP is pretty dumb but I realize...
  14. Thread: No start

    by cleatus12r
    Replies
    3
    Views
    595

    Re: No start

    Remove the chip and see if it starts. If it does, then you have a chip connection problem, a chip problem, or a calibration problem. Programming the chip with the wrong box code is not an issue and...
  15. Replies
    0
    Views
    378

    Bill, if you have time.....

    :crazy:

    The VGAE9 definition has a listing in the parameters menu (at the section 4 start) "******Do not use values below this". You weren't kidding.

    There is a guy with an E99 van I'm trying...
  16. Re: Rough idle when decelerating with new tunes on Hydra

    There is no way that stock calibrations are going to work with injectors with larger nozzles as they will do exactly what you are saying they are doing.

    For the injectors to run correctly, tuning...
  17. Replies
    6
    Views
    1,184

    Re: New to me 7.3 questions

    Here's what you need to see.

    "Tools" in menu bar (green).

    Insert your current HEX code or box code (red).

    See the recommended calibration (blue).
    165
  18. Replies
    34
    Views
    5,985

    Re: Winter project in the works.

    Just about time to park it in the shop for a heart transplant....

    Then comes new paint. Ugh.

    163164
  19. Replies
    34
    Views
    5,985

    Re: Winter project in the works.

    162The body lift is on. I'll have the bumpers on tonight. Surprisingly, it looks better to me like this than stock height.....must be my pickup-favoring DNA.

    I'll have plenty of room for some...
  20. Replies
    2
    Views
    1,324

    Re: Stacking Tunes

    With the device you have now, the 6 position chip, the only thing you would be able to "stack" with it would be something like a Banks Six Gun, Stinger, Edge Juice, or any of those injection pressure...
  21. Replies
    34
    Views
    5,985

    Re: Winter project in the works.

    Engine mounts are done. The weather isn't as nice today and working in a heavy coat sucks, especially with a hood while rolling around on a creeper.

    The engine will sit up about another 1/4" in...
  22. Replies
    34
    Views
    5,985

    Re: Winter project in the works.

    Here's last week's oil pan project. I gained an inch and a half in the front and almost three inches in the rear. The sump should fit just about flush with the bottom of the engine crossmember.
    ...
  23. Replies
    34
    Views
    5,985

    Re: Winter project in the works.

    Well, it turns out that the guy with the engine and transmission that I was supposed to go get oversold and under delivered. I drove 780 miles round trip to go look at an engine that has been sitting...
  24. Replies
    34
    Views
    5,985

    Re: Winter project in the works.

    I'm going to drive 720 miles round-trip on Tuesday to go get the new heart for the car.

    Here's a little bit of pre-fitment before the engine mounts and oil pan were fabricated....it had to go...
  25. Replies
    3
    Views
    1,372

    Re: PHP equipped rig, and others

    I like the color but never understood the appeal of that J.C.Whitney stick-on shiny stuff.
Results 1 to 25 of 88
Page 1 of 4 1 2 3 4