|
|
|||||||
| Gryphon Programmer (Disabled) Edge Product has discontinued the Edge Evolution 2, but we still provide support and tuning for it. If you have a question or comment relating the Gryphon (or Evolution) programmer, post it here. |
|
|
Thread Tools | Display Modes |
|
|
|
#1
Wed, April 21st, 2010, 03:06 PM
|
||||
|
||||
Gryphon Pod Cut-Out
Does anyone have a template of the Gryphon pod cut-out? I've got an idea and would like to use an original template if it's available. Maybe in pdf or cad format?
Thanks, Rich
__________________
Before you try and beat the odds... make sure you can survive the odds beating you! |
|
#2
Wed, April 21st, 2010, 03:10 PM
|
||||
|
||||
|
Like to cut your dash to mount it there (I was thinking about doing that with my consol before I realized how beat up it would get)? If so I would just take the rubber boot out and trace that hole onto a piece of paper.
__________________
|
|
#3
Wed, April 21st, 2010, 03:32 PM
|
||||
|
||||
|
The cutout for the boot (grommet, as they call it) or just the footprint of the programmer case?
__________________
Bill Cohron - The Mad Doctor   Power Hungry Performance - The ORIGINAL in Ford performance tuning... Since 1997! (678) 890-1110 www.gopowerhungry.com - Home of the Hydra Chip, Minotaur Tuning Software, and the new Orion Reflash System for Navistar! Bring back  Windows™ XP and 7.  Windows™ Vista and Windows™ 8 is a pain in my a$$!  Windows™ 10 is only slightly less annoying!  Windows™ 11 is garbage!  Much to my surprise, I'm actually quite enjoying Linux! 
|
|
#4
Thu, April 22nd, 2010, 12:40 AM
|
||||
|
||||
|
I'd prefer the cut-out for the boot if it's available. I got the idea from the member who had the off-road radio mount in place of the ashtray area. I've got some 1/8" black plastic (stereo installation) and going to make a panel. I'll put the programmer there with room for additional switches (back up halogens, exhaust cutout switch, aux. lights switch. I've also got carbon fiber to cover the panel and also to cover the trim piece that goes around the radio/climate control so that it will all match. Trying to do a professional job so if the cut-out template is available maybe I can avoid having to do this more than once. Just thought I'd ask.
Thanks, Rich
__________________
Before you try and beat the odds... make sure you can survive the odds beating you! |
|
#5
Thu, April 22nd, 2010, 01:12 AM
|
||||
|
||||
|
I'll see if I can get the dimensions from Edge.
__________________
Bill Cohron - The Mad Doctor Power Hungry Performance - The ORIGINAL in Ford performance tuning... Since 1997! (678) 890-1110 www.gopowerhungry.com - Home of the Hydra Chip, Minotaur Tuning Software, and the new Orion Reflash System for Navistar! Bring back Windows™ XP and 7. Windows™ Vista and Windows™ 8 is a pain in my a$$! Windows™ 10 is only slightly less annoying! Windows™ 11 is garbage! Much to my surprise, I'm actually quite enjoying Linux!
|
|
#6
Thu, April 22nd, 2010, 11:03 PM
|
|||
|
|||
|
If bill doesnt have it, I could probably take my grommet boot out and put it on the cmm and generate a cad file/program for it.
|
|
|
Flowmaster 40, PHP Gryphon, AS 2" kit
Hybrid Mode
