Pcm bracket

[O SEA D]

Originally Posted by AussieOiler

G'day Mate,
I've been lookin' at doing the same thing, but I'm not quite at that point due to wanting to finish other mods.
I'm very interested to see how you go about this.
A couple of questions, when ordering a Chip or Gryphon there is a requirement to submitt the PCM Model/Serial numbers.
Q1: Have pulled the PCM to lift these numbers?
Q2: Is there any need on our RHD models because by just removing the easily accessable bracket they can be seen??
I've had an Evo 2 in my Ftruck for some time now and have been 'sorta' happy with it. It works even better in conjunction with the JWVB that I recently installed.
Of course I returned the Evo 2 to stock settings before the VB install because I'd been running the shift firmness setting on the No+6 setting.
If I'd have left this electronic setting with the JWVB installed it would have jerked the milk out of my coffee.
But I run her for 50km in stock and noticed better shifts than with an OEM VB.
But when I stopped her and programmed it on the Tow Safe +40Hp setting it really did make a difference. Shifts quicker and has a real nice 'clunk' feel as the gears change.
Nothing radical just nice truck like shifts. I also fitted the RiffRaff Fuel Rail Cross Over (RRFx) at the same time.
Now; Why I'm interested in what your doing mate, is that I believe that I can't any longer send in my EVO2 to be upgraded to a Gryphon (not a 100% sure, but I think that's now the case).
If that is indeed the case, I'm in two minds as to either just purchase a Gryphon CS/CTS with a couple of customs,or:
Leave the Evo2 in (Set to Stock Tunning) to continue to read EOT, TFT, Boost & EGTs and put in an FU Chip.
Not sure if this is doable or even doable but not advisable (some boffin will chime in a set me straight for sure..please).
So please keep us updated on how it all turns out mate.
Out of interest, what weight is the Ftruck? What weight are you normally pulling around? What size tyres? What mods have you done in order to get the best out of a PHP Chip?
How much of this did you take into account for ordering your FU Chip tunes?
Sorry about all the questions and being a little long winded, but your the only Aussie 'pioneer' I've been able to locate going for a PHP item.
Cheers, Reg

G'day Reg I was able to pull back the plastic wheel well lining to get the code off the sticker on the PCM,but after talking to Bill he said that when I plug the Edge Evolution into the OBD11 the HEX code is shown on the Programmer and that is all he needed.

I looked into having my Evolution upgraded with custom tunes but with the cost of shipping and the fact that if I wasn't happy with any of the three tunes I would have to send it back again to be reburned it just didnt seem worth it. Not to mention the amount of time I would be without the chip due to the time it takes to ship something half way around the world.

I figured that the FU chip would be the way to go because I should never have to pay for shipping or be without my chip again and if I want to heavily mod my truck I can have custom tunes burned to the chip without having to send it back to PHP.

I think that for us fella's down here in Australia the FU chip is a great idea.

I had my truck weighed and it came in at 3400kgs and the boat is 4000kgs and my tires are a standard 265 75 R16.

I opted to go with the FU because I only have minor mods to the truck including 6637 intake,muffler delete, AIH delete and the only other mods I may consider are maybe a 38R turbo as I am fairly happy with the performance already. I dont want to push things to hard in case something goes BANG, cause the price of parts down here scares me.

Scott