|
|
|||||||
| Gryphon Programmer (Disabled) Edge Product has discontinued the Edge Evolution 2, but we still provide support and tuning for it. If you have a question or comment relating the Gryphon (or Evolution) programmer, post it here. |
|
|
Thread Tools | Display Modes |
|
|
|
#1
Thu, April 22nd, 2010, 01:12 AM
|
||||
|
||||
I'll see if I can get the dimensions from Edge.
__________________
Bill Cohron - The Mad Doctor   Power Hungry Performance - The ORIGINAL in Ford performance tuning... Since 1997! (678) 890-1110 www.gopowerhungry.com - Home of the Hydra Chip, Minotaur Tuning Software, and the new Orion Reflash System for Navistar! Bring back  Windows™ XP and 7.  Windows™ Vista and Windows™ 8 is a pain in my a$$!  Windows™ 10 is only slightly less annoying!  Windows™ 11 is garbage!  Much to my surprise, I'm actually quite enjoying Linux! 
|
|
#2
Thu, April 22nd, 2010, 11:03 PM
|
|||
|
|||
|
If bill doesnt have it, I could probably take my grommet boot out and put it on the cmm and generate a cad file/program for it.
|
|
#3
Sat, April 24th, 2010, 12:09 AM
|
||||
|
||||
|
Thanks guys... I appreciate the offer but this wasn't intended to make work for anyone. I just thought I'd ask if there was already a template file available. If there isn't, I can go old-school... not a problem. But please... don't go out of the way. I only meant that if someone could attach it to an email with a couple of clicks. Anything more than that just isn't worth their trouble.
Again... thanks. I'll post pics once I finish up.
__________________
Before you try and beat the odds... make sure you can survive the odds beating you! |
|
#4
Sat, April 24th, 2010, 10:01 AM
|
||||
|
||||
|
You just gave an idea I could do with mine. I could put mine below my stereo. My original intentions for that space was going to be for putting aux switches but I should be able to fit a couple switches and my Gryphon.
__________________
|
|
#5
Sun, April 25th, 2010, 05:16 PM
|
||||
|
||||
|
Nice! I like the diamond plate
I was thinking about doing the same thing once I got around to upgrading the stereo.
__________________
|
|
#6
Sat, May 1st, 2010, 04:11 PM
|
||||
|
||||
|
Here's some pics of the finished project.
I used some 1/8" plastic sheets found on ebay. They're already scribed at 1/4" increments on the back side (as well as some circular scribes for gauges, etc..). The size of the panel that replaces the ashtray flip-out is 9"w x 3"h. I then used M4 bolts / nyloc-nuts to mount with nylon spacer standoffs. 1/2" stand-off for the top bolts and 1/4" stand-off for the bottom bolts. I also purchased a carbon-fiber fabric for interior upholstery from ebay (yes... ebay addict here). Then using spray adhesive, I covered the new panel. So that the carbon-fiber look would match, I also scuffed and covered the trim panel (climate controls, radio, etc...) with the same. Turned out well I think. I mounted the pod to the left so that I have room to mount switches, accessories at a later time. Plans are to add an exhaust cut-out and the hella grill with the halogen lights. Switches for both will end up in the extra space to the right of the Gryphon.
__________________
Before you try and beat the odds... make sure you can survive the odds beating you! |
|
#7
Sat, May 1st, 2010, 05:11 PM
|
||||
|
||||
|
Very nice!
__________________
|
|
#8
Sun, May 2nd, 2010, 06:05 AM
|
||||
|
||||
|
Looks great. Good job. Is it weird to look down there to read the engine parameters? I watch mine all the time and wouldn't want mine that low.
__________________
|
| Thread Tools | |
| Display Modes | |
|
|
Flowmaster 40, PHP Gryphon, AS 2" kit
Hybrid Mode
