Power Hungry Performance Forum  

Go Back   Power Hungry Performance Forum > Ford Super Duty & Excursion > 1994½ to 1997 7.3L Power Stroke Diesel

1994½ to 1997 7.3L Power Stroke Diesel
7.3L Power Stroke Diesel equipped F-Series and F-Super Duty.


Reply
 
Thread Tools Display Modes
  #1  
Old Sat, January 9th, 2010, 09:46 PM
majek5's Avatar
majek5 majek5 is offline
Nothin' Stock
 
Join Date: Nov 2009
Location: Northern Illinois
Posts: 209
majek5 is on a distinguished road
Default UVCH

What are the symptoms that would lead to changing these? Do they wear out?
__________________
'06 6.0 F350 CCLB KR.

stock...
Reply With Quote
  #2  
Old Sat, January 9th, 2010, 10:00 PM
907DAVE's Avatar
907DAVE 907DAVE is offline
BROKE
 
Join Date: Oct 2009
Posts: 1,340
907DAVE will become famous soon enough
Default

Typically the connector comes unhooked from the gasket, and ford sells a insert that helps hold them together. The symptoms for this would be a CEL, running rough(can be intermittent), and if resistance is affected it will fail a buzz test for one or more cylinders.

As far as the harness wearing out, when you have glow plugs that pull too many amps the harness and connectors can melt and make them impossible to separate from each other, and will ruin connector pins, as well as a small section of the engine wire harness. Symptoms would be a hard start, or running rough for a few minutes when cold.
Reply With Quote
  #3  
Old Sun, January 10th, 2010, 10:26 AM
cleatus12r's Avatar
cleatus12r cleatus12r is offline
F Your Yankee Blue Jeans
 
Join Date: Jan 2009
Location: Somewhere in Montana
Posts: 2,654
cleatus12r is a name known to allcleatus12r is a name known to allcleatus12r is a name known to allcleatus12r is a name known to allcleatus12r is a name known to allcleatus12r is a name known to all
Default

A very common failure results from oil intrusion into the connectors. The oil will get between mating terminals (inside the connector) and cause resistance. Resistance equals heat. Once the terminals get warm, they loose tension on their mating terminal and begin to melt.

Usually the connector inside the valve cover gasket will come halfway unplugged and cause glow plug concerns and in extreme cases, IDM codes for injector circuit problems. Keep in mind that once an injector circuit is suspected to be open by the IDM that the IDM will kill the entire bank of injectors.

The 95-97 trucks seem to be less susceptible to connector separation.

Good call, Dave.
__________________
Tuning, flashing, burning chips, and repairing all aspects of 7.3L Powerstrokes.
SEVEN 7.3L-powered vehicles in the driveway. Two didn't come that way from the factory!
Reply With Quote
  #4  
Old Sat, February 6th, 2010, 10:31 AM
Brown Falcon's Avatar
Brown Falcon Brown Falcon is offline
Addicted to Ford!
 
Join Date: Nov 2009
Location: New Bern, NC / Corvallis, OR
Posts: 21
Brown Falcon is on a distinguished road
Default

Mine just all of a sudden stoppped running on 4 cylinders... turned out to be burned out pins and a melted connector on the engine side of the harness that plugs into the VC gasket plug.

Replaced both harnesses inside the VC, VC gasket harness, glowplugs on that side, and the burned out connector on the outside for about $200
__________________

Brownie - USMC - OohRah!
1995 F350, 7.3 PSD, PHP Phoenix Chip, 140V IDM, HPX, 6637 Air Filter, 3" DP, 4" Exhaust, Lost Kitty!
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:15 PM.


All Contents Copyright 2008-2024, Power Hungry Performance