|
|
|||||||
| F.U. Chip & FU2 Flex Chip (DISCONTINUED) (Disabled) If you have a question or comment relating the new F.U. Chip or FU2 Flex Chip, post it here. |
|
|
Thread Tools | Display Modes |
|
#1
Thu, January 12th, 2012, 11:05 PM
|
|||
|
|||
No start... Need advice
I installed my chip. At first it started fine but the chip didn't work. I removed it all and cleaned the contacts some more. After that it wouldn't start. Cleaned it a little bit more and it started for a few seconds then died. If I unplug the chip the truck runs fine and starts right up. I used a brass brush and some emery cloth to clean it. Mine had a lot of silicone on it. Do y'all think that I could be that it's just not making food contact?
Stupid is as stupid does.
__________________
02 f250, 7.3,4r100 rebuilt at 140k with shift kit and triple disc. Dana 60, 2.5" zone leveling kit, 16x10s, 315/75r/16 Autoenginuity in the Lafayette,La area 
|
|
#2
Thu, January 12th, 2012, 11:15 PM
|
||||
|
||||
|
Since this is in the FU section, I assume you have an FU chip.
Did you flash any calibrations to the chip initially? They are sent out blank. |
|
#3
Fri, January 13th, 2012, 05:27 AM
|
|||
|
|||
|
No start... Need advice
Yes. I have the fu. I did burn the chip. My high idle did work for a few seconds
Stupid is as stupid does.
__________________
02 f250, 7.3,4r100 rebuilt at 140k with shift kit and triple disc. Dana 60, 2.5" zone leveling kit, 16x10s, 315/75r/16 Autoenginuity in the Lafayette,La area
|
|
#4
Fri, January 13th, 2012, 11:00 AM
|
||||
|
||||
|
Sounds to me like there is something amiss between the chip and the PCM circuit board if it worked at some point.
|
|
#5
Fri, January 13th, 2012, 06:04 PM
|
|||
|
|||
|
No start... Need advice
I got it. Took the PCM out today and in the sunlight I could tell that it wasn't clean enough. Scraped some more silicone off with a toothpick and passed some scotch bright over it after to finish. Working flawlessly. The power from this chip is unreal. Feels like a new truck
Stupid is as stupid does.
__________________
02 f250, 7.3,4r100 rebuilt at 140k with shift kit and triple disc. Dana 60, 2.5" zone leveling kit, 16x10s, 315/75r/16 Autoenginuity in the Lafayette,La area
|
|
#6
Fri, January 13th, 2012, 11:20 PM
|
||||
|
||||
|
I'm currently making a video of how to clean the connector right the first time!
|
|
#7
Sat, January 14th, 2012, 12:18 PM
|
|||
|
|||
|
No start... Need advice
That's good man. Doing it in te sunlight vs in the shop with a flashlight helped alot
Stupid is as stupid does.
__________________
02 f250, 7.3,4r100 rebuilt at 140k with shift kit and triple disc. Dana 60, 2.5" zone leveling kit, 16x10s, 315/75r/16 Autoenginuity in the Lafayette,La area
|
|
#8
Tue, January 17th, 2012, 03:30 PM
|
|||
|
|||
|
Brass Brush is the ONLY way to clean it right the first time IMO.
__________________
2002 7.3 F250 Supercab Shortbox DIY intake CCV dumped Autometer gauges WW/ATS 1.0 exhaust housing Hutch/Harpoon in tank mods/hpX line AIH delete/ebpv delete TruCool trans cooler Straight piped PHP FU 
|
|
|
Linear Mode
