|
|
|||||||
| 1999 to 2003 7.3L Power Stroke Diesel 7.3L Power Stroke Diesel equipped Super Duty and Excursion. |
 |
|
|
Thread Tools | Display Modes |
|
#1
Wed, September 26th, 2012, 08:01 PM
|
|||
|
|||
PMR Rod Replacement for my 2003 7.3L
Random question. I have a buddy who is pulling a 88-97 IDI 7.3L out of a truck he is building into a rock crawler. Not sure of the exact year of the engine because it is a rebuild. The engine is fine but he wants to put a 6.9 in it.
From the minimal research I have done this thing has Forged rods. He said I could have them if I wanted to dig them out of the block. Would those rods fit in my 2003 7.3L? Does anyone know any specific reasources where I could find this out? It would be awsome if I could swap the rods into my truck so I can get Bill to put more power to it. Thanks Joe
__________________
 2003 4x4 F350 Super Duty Crew Cab Short Bed4" Down pipe and exhaust, Wicked Wheel, Modified Exhaust Turbo Housing, Big Head Waste Gate Actuator, PML Transmission Pan, Factory Tech Valve Body, Autometer Gage Pod, PHP FU2 Chip 
|
|
#2
Thu, September 27th, 2012, 01:35 PM
|
|||
|
|||
|
__________________
01 F350 7.3 4x4 CC SRW/3.73/315-75-16/Aeroforce Interceptor/BD Thruster II/ Bellowed Up-Pipes/4" turbo back exhaust/CCV Mod/DIY 6637/FPR Shimmed to 65 PSI/TS chip reburned with PHP tunes (Stock, 40T WITH Whsiper tune, 80DD, 100R, 140Ex, 140SS)/Replaced and Cleaned EBPS & Tube 4-6-12/Zoodad mod/Recon smoked cab lights/MM Hubs/Cowl Hood/HPx
|
|
#3
Thu, September 27th, 2012, 01:38 PM
|
|||
|
|||
|
Have you visually checked to verify 100% that you have PMR's? I've seen 02's with factory forged rods...one member post yesterday on TDS verified his 02 has forged rods. It's a long shot, but its not really too hard to check.
__________________
01 F350 7.3 4x4 CC SRW/3.73/315-75-16/Aeroforce Interceptor/BD Thruster II/ Bellowed Up-Pipes/4" turbo back exhaust/CCV Mod/DIY 6637/FPR Shimmed to 65 PSI/TS chip reburned with PHP tunes (Stock, 40T WITH Whsiper tune, 80DD, 100R, 140Ex, 140SS)/Replaced and Cleaned EBPS & Tube 4-6-12/Zoodad mod/Recon smoked cab lights/MM Hubs/Cowl Hood/HPx
|
|
#4
Thu, September 27th, 2012, 04:06 PM
|
|||
|
|||
|
How do you check? The engine is currently in the truck and running.
__________________
2003 4x4 F350 Super Duty Crew Cab Short Bed4" Down pipe and exhaust, Wicked Wheel, Modified Exhaust Turbo Housing, Big Head Waste Gate Actuator, PML Transmission Pan, Factory Tech Valve Body, Autometer Gage Pod, PHP FU2 Chip
|
|
#5
Thu, September 27th, 2012, 04:09 PM
|
|||
|
|||
|
Ramertide,
Just to make sure the "PSD rods" refered to in the thread you provided a link for refer to my truck?
__________________
2003 4x4 F350 Super Duty Crew Cab Short Bed4" Down pipe and exhaust, Wicked Wheel, Modified Exhaust Turbo Housing, Big Head Waste Gate Actuator, PML Transmission Pan, Factory Tech Valve Body, Autometer Gage Pod, PHP FU2 Chip
|
|
#6
Sat, September 29th, 2012, 12:08 AM
|
|||
|
|||
|
PSD=Powerstroke Super Duty..... Super Duty=99-03 F-Series (guess it could cover all models since 99 to current date).
Everything else is OBS=Old Body Style or everything pre-99 Ill look for the rod inspection port link. IIRC the link was broken last time I pulled it up.
__________________
01 F350 7.3 4x4 CC SRW/3.73/315-75-16/Aeroforce Interceptor/BD Thruster II/ Bellowed Up-Pipes/4" turbo back exhaust/CCV Mod/DIY 6637/FPR Shimmed to 65 PSI/TS chip reburned with PHP tunes (Stock, 40T WITH Whsiper tune, 80DD, 100R, 140Ex, 140SS)/Replaced and Cleaned EBPS & Tube 4-6-12/Zoodad mod/Recon smoked cab lights/MM Hubs/Cowl Hood/HPx
|
|
#7
Sat, September 29th, 2012, 12:19 AM
|
|||
|
|||
|
Can't find link. But you see the the rods (part of em) through the inspection port above the furl filter housing. It takes 5/16 bar stock to fit into the plug. I've also heard of some people using thick flat head screw driver. If you can't see anything, bump the starter. It's hard searching on my phone. Google "7.3 rod inspection port". Disregard what you read about serial numbers. It'd been debunked several times.
__________________
01 F350 7.3 4x4 CC SRW/3.73/315-75-16/Aeroforce Interceptor/BD Thruster II/ Bellowed Up-Pipes/4" turbo back exhaust/CCV Mod/DIY 6637/FPR Shimmed to 65 PSI/TS chip reburned with PHP tunes (Stock, 40T WITH Whsiper tune, 80DD, 100R, 140Ex, 140SS)/Replaced and Cleaned EBPS & Tube 4-6-12/Zoodad mod/Recon smoked cab lights/MM Hubs/Cowl Hood/HPx
|
|
#8
Sat, September 29th, 2012, 12:23 AM
|
|||
|
|||
|
Awesome thanks for the info. One more question. What I am I looking for to tell the difference between pmr and forged?
__________________
2003 4x4 F350 Super Duty Crew Cab Short Bed4" Down pipe and exhaust, Wicked Wheel, Modified Exhaust Turbo Housing, Big Head Waste Gate Actuator, PML Transmission Pan, Factory Tech Valve Body, Autometer Gage Pod, PHP FU2 Chip
|
|
#9
Sat, September 29th, 2012, 01:30 AM
|
|||
|
|||
|
Awesome thanks for the info. One more question. What I am I looking for to tell the difference between pmr and forged?
__________________
2003 4x4 F350 Super Duty Crew Cab Short Bed4" Down pipe and exhaust, Wicked Wheel, Modified Exhaust Turbo Housing, Big Head Waste Gate Actuator, PML Transmission Pan, Factory Tech Valve Body, Autometer Gage Pod, PHP FU2 Chip
|
|
#10
Sun, September 30th, 2012, 11:18 AM
|
|||
|
|||
|
__________________
01 F350 7.3 4x4 CC SRW/3.73/315-75-16/Aeroforce Interceptor/BD Thruster II/ Bellowed Up-Pipes/4" turbo back exhaust/CCV Mod/DIY 6637/FPR Shimmed to 65 PSI/TS chip reburned with PHP tunes (Stock, 40T WITH Whsiper tune, 80DD, 100R, 140Ex, 140SS)/Replaced and Cleaned EBPS & Tube 4-6-12/Zoodad mod/Recon smoked cab lights/MM Hubs/Cowl Hood/HPx
|
|
|
|
Linear Mode
