![]() |
|
Gryphon Programmer (Disabled) Edge Product has discontinued the Edge Evolution 2, but we still provide support and tuning for it. If you have a question or comment relating the Gryphon (or Evolution) programmer, post it here. |
|
Thread Tools | Display Modes |
|
#1
|
||||
|
||||
![]()
Changed the one in "gryphon programmers" already.
__________________
SENIOR MODERATOR--PTLA God doesn't have a Facebook but he's my friend. God doesn't have a twitter, but I follow him. |
#2
|
|||
|
|||
![]()
Well I just got my Gryphon today and quickly installed it. I think I can patiently wait on my custom tunes and just leave my truck on 0 (stock). But running level 1 transmission only shouldn't be a problem at all right? Seeing as how it has no engine modifications.?.? While I wait I guess I could try to figure out how to put in my tire size. 35x12.50x18. Anyone have this size and remember the mm value?
|
#3
|
||||
|
||||
![]()
Yes, the level 1 should be fine until then.
Tire size should be 2760 mm. That'll get you really close.
__________________
Bill Cohron - The Mad Doctor ![]() ![]() ![]() Power Hungry Performance - The ORIGINAL in Ford performance tuning... Since 1997! (678) 890-1110 www.gopowerhungry.com - Home of the Hydra Chip, Minotaur Tuning Software, and the new Orion Reflash System for Navistar! Bring back ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() Much to my surprise, I'm actually quite enjoying Linux! ![]() |
#4
|
|||
|
|||
![]()
Great! Thanks a lot!
|
#5
|
|||
|
|||
![]()
I looked through the book again, and decided that I would do the math for the tire conversion just because thats how I am. I went and got the actual specs for my tires off of Nitto's website and its 35.04x13.39x18. Seems wide for a 35x12.50, but thats what it says the actual width is. I have punched in the numbers and did the math several times and it looks like I should be more around 2715 to 2720. Just curious, where did 2760 come from? Thanks, Travis
|
#6
|
||||
|
||||
![]()
I've noticed Bill seems to use a "squish" value that is less than what I've found works for me. If the unloaded circumference is about 2793mm, I would actually try 2709mm, which corresponds to a 3% reduction due to "squish".
However, anything you try (and your numbers seem reasonable too) is just a starting place. Plug it in and see how close the Gryphon's speed reading is to a GPS or how close it is to driving a measured mile at a constant speed and dividing the time in seconds into 3600. Adjust as necessary to make the Gryphon match the GPS or computed speed. (The dash speedo usually reads about 3% faster than the actual speed, by the way). - Jack
__________________
2024 F150 Platinum SCrew 3.5L PowerBoost FX4, Peragon Tonneau Cover, LineX Bed, 35% Window Tint on All Sides and Rear, Full Nose Paint Protection Film, Husky Mud Guards, Lasfit Floor Liners, VIOFO Dash Cam |
#7
|
|||
|
|||
![]()
Okay, sounds good. Thanks a lot. Another question. I read that when I first initially run a tune that I should not go in and customize any of the options. Since I don't have my custom tunes yet, I am currently running Tranny Only
(1). I chose no on the customize option. Now, when I go in with my custom tunes OR if I decide to change up and go to the Tow tune, if I chose yes for customize and set up my tire size, is that going to save it for every tuning level or just the current one that I have selected to run at that time? In other words, do I have to customize my tire size for each individual tune level? |
Thread Tools | |
Display Modes | |
|
|