strokin'_tatsch
Sun, February 14th, 2010, 08:10 PM
Hi, just checkin' into this forum. i'm on many other forums, but i like to check all of them out from time to time. Not a PHP customer at this time, but perhaps sometime down the road. Not new to modding my diesel, but when it comes to my gasser... Well i did build the engine, but getting it to run seems to be becoming a pain b/c i can't find a factory 5.0 mass air flow harness from an F150 and i'm not too sure how to mod the original harness to run the MAF so its been sitting for close to a year now. LoL
Longshot270
Sun, February 14th, 2010, 08:39 PM
'Bout time you got over here! :hehe:
When did you get a gasser?...and why?
Longshot270
Sun, February 14th, 2010, 09:04 PM
Oh and your gonna like this forum because there is a ton of good info and we dont put up with much BS like on some of the others.
On that note lets leave some of the mud slinging for the pasture. ;)
907DAVE
Sun, February 14th, 2010, 09:10 PM
Ford Racing wont sell just the harness?
I got mine in a kit, but do not see why they would not separate it.
Ohh and WELCOME!:howdy:
Buddy Starr
Sun, February 14th, 2010, 11:46 PM
Welcome
JWBFX4
Mon, February 15th, 2010, 12:08 AM
Welcome :howdy:
88Racing
Mon, February 15th, 2010, 12:25 AM
Welcome!:)
Power Hungry
Mon, February 15th, 2010, 02:39 AM
Travis,
Glad to have you around, dude! Catch ya round the fuel pumps. :2thumbs:
strokin'_tatsch
Mon, February 15th, 2010, 11:28 PM
'Bout time you got over here! :hehe:
When did you get a gasser?...and why?
i got roy's old copper F-150. i'm in the middle of swapping in a 5.0 into it. the engine going into now has flat top higher compression pistons, cryo'd rods, new bearings and all clearances are awesome, Ford Racing B303 cam, GT40P heads ported, port matched upper and lower typhoon intakes, Ford Racing 1.72:1 roller rockers, chromoly pushrods, new roller lifters, comp double roller timing set, smog eliminator, MAF conversion(in progress), 70mm throttle body, EGR eliminator, throttle body spacer, MSD pro billet, MSD blaster 2 coil, taylor 409 wires, and probably go with an air raid filter or something. dang i have spent too much money on that truck already. i still have to order the MSD, throttle body, and EGR eliminator along with a 6" lift and put these BFG muds on there with my rockcrawler streetlock wheels. LoL. Oh yeah, and it's got ceramic coated shorty headers, high volume oil pump, ARP head bolts, etc. i think it should be able to handle a little nitrous and some boost too. i didn't do a girdle or very heavy springs, but if i decide that nitrous or a supercharger is in need then i will throw on a girdle and heavier springs to keep it running happy. haha
Oh and your gonna like this forum because there is a ton of good info and we dont put up with much BS like on some of the others.
On that note lets leave some of the mud slinging for the pasture. ;)
i'm on a ton of forums buddy. i check them all frequently so i will be around here. i think i'm on 9 or 10 forums total now. LoL
Travis,
Glad to have you around, dude! Catch ya round the fuel pumps. :2thumbs:
Bill, i'm glad to be here brother. i will see ya over on PSN. haha. need to see if you can tune my gasser. it's a '94 F-150, but it will have a mustang A9L computer in it. haha