|
|
|||||||
| 1997 to 2003 F-150 4.2L, 4.6L, and 5.4L equipped F-150s. |
 |
|
|
Thread Tools | Display Modes |
|
#1
Wed, July 21st, 2010, 11:16 AM
|
|||
|
|||
Gryphon says its locked to another vehicle??
2002 Ford F150 5.4 2wd with a gryphon for a little over 2 years now i think. it's never been hooked up to another vehicle and has only been removed 2 or 3 times since i've had it. it hasnt been removed in the past 4 months. i have level 1 loaded (i have custom tunes) and went to change it last night to level 2 and it says that it's locked to another vehicle. this is the first time it's ever happened.
i tried returning it to stock, all 3 levels, even customizing a tune but it wont let me do anything. the only thing i can think that has happened since the last time i changed the tune (about a month) is my battery died on my truck for about 2 days... it's been dead before but never where i could access my tunes and change them out... any suggestions? 
|
|
#2
Wed, July 21st, 2010, 12:44 PM
|
||||
|
||||
|
Here's an idea to try.....
Unplug the unit, turn the key on, then plug the programmer back in.
__________________
Tuning, PCM flashing, and burning chips for 7.3s since 2008. Repairing all aspects of 7.3L Powerstrokes for 25 years. Eight 7.3L PSDs in the driveway including a 1994 Crown Vic and 1973 F100/2002 F350. Looking for the next victim.
|
|
#3
Wed, July 21st, 2010, 07:29 PM
|
||||
|
||||
|
Quote:
 - Jack
__________________
 2024 F150 Platinum SCrew 3.5L PowerBoost FX4, Peragon Tonneau Cover, LineX Bed, 35% Window Tint on All Sides and Rear, Full Nose Paint Protection Film, Husky Mud Guards, Lasfit Floor Liners, VIOFO Dash Cam
|
|
#4
Thu, July 22nd, 2010, 12:01 AM
|
|||
|
|||
|
ok, what else??? i've done that about 20 times over the last few days without even knowing that was a solution... it's REALLY got me stumped... thanks for the quick reply you guys.. but still a no go
|
|
#5
Thu, July 22nd, 2010, 11:25 AM
|
||||
|
||||
|
Quote:
- Jack
|
|
#6
Thu, July 22nd, 2010, 12:17 PM
|
|||
|
|||
|
gotcha. i think i have another cable laying around here somewhere that i will try.. thanks man!!
|
|
#7
Thu, July 22nd, 2010, 12:43 PM
|
||||
|
||||
|
Cable Problem==Call PHP!!!!!!!
Get another one so your truck doesn't become disabled. Don't mess with programming it anymore until you get a new cable.
__________________
SENIOR MODERATOR--PTLA God doesn't have a Facebook but he's my friend. God doesn't have a twitter, but I follow him.
|
|
#8
Fri, July 23rd, 2010, 11:30 AM
|
|||
|
|||
|
when i first got the programmer i had a cable issue with it.... but that's been going on 3 years ago..
don't worry about messing with the programming... lol i can't. but my truck IS running rough and throwing lean code and its time for emission test
|
|
#9
Fri, July 23rd, 2010, 12:54 PM
|
||||
|
||||
|
Quote:
This would be really helpful. There's a number of problems that could be causing those codes. I'll post a note for the administration.
__________________
SENIOR MODERATOR--PTLA God doesn't have a Facebook but he's my friend. God doesn't have a twitter, but I follow him.
|
|
#10
Fri, July 23rd, 2010, 02:14 PM
|
|||
|
|||
|
no the codes are ok... i've been doing diagnostic work on it for the past month and half. basically bank 1 and 2 lean. every now and then a heated 02 sensor, but i'm in the process of changing them out. i was doing good and not throwing any codes when i run level 2 and driving right, thats why i was changing it back.
as far as the codes go, really isn't much more i can replace on the motor so now i'm just down to the itty bitty stuff.
|
|
|
|
Linear Mode
