Troyer Valve Body

Punisher · #1 Fri, January 15th, 2010, 09:08 AM

I'm installing the Troyer Transmission Valve Body upgrade today. I have the Gryphon Tuner with canned tunes (waiting on custom tunes to be written).

Any suggestions as to which canned tune to run until custom tunes are sent?

Thanks,
-Rich

***Jackpine*** · #2 Fri, January 15th, 2010, 02:22 PM

Quote:

Originally Posted by Punisher

I'm installing the Troyer Transmission Valve Body upgrade today. I have the Gryphon Tuner with canned tunes (waiting on custom tunes to be written).

Any suggestions as to which canned tune to run until custom tunes are sent?

Thanks,
-Rich

Ugh! I imagine 88Racing has better advice than me, but I'd think the Level 0 (stock) tune might be the safest bet here. And, Bill needs to know that you have the VB upgrade so he can adjust your tunes accordingly.

- Jack

***88Racing*** · #3 Fri, January 15th, 2010, 07:01 PM

If you run any of the canned tunes you are going to want to take it for a gentle test drive. You are going to have to reduce your shift firmnes in each shift by -3 to -7.
Bill's advice to me was to try it gently and if to harsh reduce the shift firmness.
I was planning on doing this mod also.
Look in calibration requests for my thread.

***88Racing*** · #4 Fri, January 15th, 2010, 07:26 PM

Here's a link to that thread:
http://forum.gopowerhungry.com/calib...y-upgrade.html

Punisher · #5 Sat, January 16th, 2010, 01:06 AM

Quote:

Originally Posted by JackandJanet

Ugh! I imagine 88Racing has better advice than me, but I'd think the Level 0 (stock) tune might be the safest bet here. And, Bill needs to know that you have the VB upgrade so he can adjust your tunes accordingly.

- Jack

I mentioned this when I placed the order and I believe you noted it on my invoice (#2564 / Hex: RXDG5AA). If you'll double check just to make sure I'd appreciate it.

Thanks,
Rich (aka Punisher)

88Racing: Thanks for the link. I'll research it and proceed cautiously. Thanks!!!

***88Racing*** · #6 Sat, January 16th, 2010, 08:58 AM

Quote:

Originally Posted by Punisher

I mentioned this when I placed the order and I believe you noted it on my invoice (#2564 / Hex: RXDG5AA). If you'll double check just to make sure I'd appreciate it.

Thanks,
Rich (aka Punisher)

88Racing: Thanks for the link. I'll research it and proceed cautiously. Thanks!!!

Corey or Bill will need to double check it when they get back. Ok?
There is also a seperator plate "C" mod that only runs $85.

Punisher · #7 Mon, January 18th, 2010, 12:45 AM

Quote:

Originally Posted by 88Racing

Corey or Bill will need to double check it when they get back. Ok?

My apologies... I'm still learning names/nicks, who works at PHP, who is providing helpful advice. I wasn't paying close enough attention to who posted and thought it was Corey/Bill. I didn't mean to be rude or insensitive. My error!

***88Racing*** · #8 Mon, January 18th, 2010, 01:00 AM

Quote:

Originally Posted by Punisher

My apologies... I'm still learning names/nicks, who works at PHP, who is providing helpful advice. I wasn't paying close enough attention to who posted and thought it was Corey/Bill. I didn't mean to be rude or insensitive. My error!

Corey=Groovy Chick=PHP owner=Admin
Bill=Power Hungry=PHP owner=Admin
Lars=88racing=PHP volunteer=Senior Moderator
Jack=JackandJanet=PHP volunteer=Super Moderator
Cody=Cleatus12r=PHP volunteer=Senior Moderator
Jeremy=Jeremy=PHP volunteer=Moderator
Everyone else are really good people with great advice.
Hope this helps.