Strange Noises (tranny?, transfer?)

***88Racing*** · #1 Mon, July 13th, 2009, 01:13 PM

That noise would worry me also!

What kind of adjustment have you done with the evo and tranny?

Any vibration inthe driveline or steering wheel?

Lars

***Jackpine*** · #2 Mon, July 13th, 2009, 02:19 PM

You can't really change the shift pressure with an Edge or a Gryphon. All you can change is the time it takes for the clutch to lock up during shifts (shift firmness).

Thump-thump doesn't sound like a transmission issue to me anyway. What it DOES suggest to me is a bad CV joint. Does the sound get more noticeable during a turn? I THINK you have a 4x4 - have you looked at the driveaxle boots? If they're cracked or otherwise damaged, I think that's the problem.

- Jack

Kurt14 · #3 Mon, July 13th, 2009, 02:43 PM

Quote:

Originally Posted by 88Racing

That noise would worry me also!

What kind of adjustment have you done with the evo and tranny?

Any vibration inthe driveline or steering wheel?

Lars

To begin with I turned the firmness up high, but later learned it wasn't the best idea.. It's not turned down, way down.. No vibrations in the steering wheel other than it's slightly out of align, haha... Yea, this noise have bothered me for quite sometime.. it's just now getting a little louder...

* JACK AND JANET *

It stays the same if I am going straight or in a turn... I have read about the front not disengaging correctly but I just haven't ruled anything out other than U-joints and Gears.. I'll research the front drive components today. By the way it only have 67,000 miles on everything...

Thanks for the help guys...

***88Racing*** · #4 Mon, July 13th, 2009, 03:57 PM

If you have a lift kit? Start checking some of the components of the kit also to make sure the driveline isn't binding or rubbing.

Lars

Kurt14 · #5 Mon, July 13th, 2009, 04:12 PM

Quote:

Originally Posted by 88Racing

If you have a lift kit? Start checking some of the components of the kit also to make sure the driveline isn't binding or rubbing.

Lars

Will do! I am leveled out with a 2.5 Daystar kit... Thanks a ton...

Kurt14 · #6 Tue, July 14th, 2009, 02:27 PM

Checked the entire front components... The drive boots look brand new so unless it's internal the CV's looked perfect.. The one thing I did notice is marks on my coil spring but I believe they are there from when I have had it on the lift at work and school and the A-arm drops down onto the spring and caused a little mark.. That was all I could find up front. The steering looks great, the front chunk is spotless.. How exactly do I check the angle on the driveline to tell if that is my noise?

***88Racing*** · #7 Tue, July 14th, 2009, 02:52 PM

You have a lift!
Put the truck up on it if its a 2 post and turn every wheel by hand and you or your buddy go around and listen. Do you have a yolk bearing support on the drive shaft?
Check the wheel lugs.
Do you have access to a dyno? If you do just put it on there and go for a drive and have your friends listen also.
I am running out of ideas!

Lars

Kurt14 · #8 Tue, July 14th, 2009, 02:57 PM

Quote:

Originally Posted by 88Racing

You have a lift!
Put the truck up on it if its a 2 post and turn every wheel by hand and you or your buddy go around and listen. Do you have a yolk bearing support on the drive shaft?
Check the wheel lugs.
I am running out of ideas!

Lars

I will try to put it on the lift tonight.. Need to rotate the tires anyway.. Only thing done to the drive shaft from factory is that I have Dana/Spicer U-joints instead of factory.. Yea, I have run out of ideas as well.. It's driving me nuts..