Power Hungry Performance Forum  

Go Back   Power Hungry Performance Forum > Power Hungry Performance Product Information > Gryphon Programmer (Disabled)

Gryphon Programmer (Disabled)
Edge Product has discontinued the Edge Evolution 2, but we still provide support and tuning for it.

If you have a question or comment relating the Gryphon (or Evolution) programmer, post it here.


 
 
Thread Tools Display Modes
  #1  
Old Wed, September 22nd, 2010, 07:38 PM
FORDRDRFX4LIFE's Avatar
FORDRDRFX4LIFE FORDRDRFX4LIFE is offline
FORDFX
 
Join Date: Jul 2009
Location: SOUTH ORANGE COUNTY ,CA
Posts: 35
FORDRDRFX4LIFE is on a distinguished road
Default dealer flashed my truck

hello as the title says i took truck in to dealer cause i needed some ork done on her and i ot truck back today and noticed when i put my programmer ack on it couldnt find an ecm so im guessing i need a new code so my question is what do i need to fill out so bill can gi me a new code so my gryphon works thnx
__________________
2008 F150 FX4 BLACKED OUT 2.5" LEVELING KIT STAGE 2 AFE INTAKE FLOWMASTER SERIES 40 TURN DWN 3" PIPE 285/65/R18 GRANETE ALLOY ULTRA BLACK MAGNUS RIMS WITH NITTO TERRA GRAPPLERS..COMING SOON GRYPHON CUSTOM 91 TUNES
  #2  
Old Wed, September 22nd, 2010, 08:33 PM
LonestarROB's Avatar
LonestarROB LonestarROB is offline
Lonestar Legend
 
Join Date: Nov 2009
Location: Plano Tx
Posts: 95
LonestarROB is on a distinguished road
Default

YOU don't need a new code, your truck(should) have a new HEX code because of the flash. Thus the reason it doesn't work. You'll need new tune/s.

This is what it says in big red letters at the top of this forum...

"IF YOUR PCM IS REFLASHED, YOUR GRYPHON WILL NOT WORK -- CURRENT CUSTOM TUNING CHARGES WILL APPLY TO REWRITE YOUR CUSTOM CALIBRATIONS!"

  #3  
Old Wed, September 22nd, 2010, 10:19 PM
Longshot270's Avatar
Longshot270 Longshot270 is offline
Forum Predator
 
Join Date: Jul 2009
Location: DFW, TX
Posts: 1,878
Longshot270 will become famous soon enough
Default

Before you go through with ordering new tunes try turning the key to the on position (without the engine running), unplugging the gryphon, wait a few seconds then plug it back in. See if that does anything.
__________________
  #4  
Old Thu, September 23rd, 2010, 05:40 PM
Jackpine's Avatar
Jackpine Jackpine is offline
PHP Groupie
 
Join Date: Nov 2008
Location: Among Elk, Deer and Javalinas on the Mogollon Rim in Aridzona
Posts: 3,243
Jackpine is a name known to allJackpine is a name known to allJackpine is a name known to allJackpine is a name known to allJackpine is a name known to allJackpine is a name known to all
Default

Yes, do as Longshot says and then, even if the PCM WAS reflashed, you should at least be able to read the hex code when you plug the Gryphon in. If the code is different, you WERE reflashed.

But, it really sounds like you did not allow the Gryphon to boot properly. The ignition key has to be ON (engine off) before you plug in the Gryphon. (Note: this advice does not seem to apply to the newer CS/CTS units - they seem happy with the ignition in either state.)

- Jack
__________________

2024 F150 Platinum SCrew 3.5L PowerBoost FX4, Peragon Tonneau Cover, LineX Bed, 35% Window Tint on All Sides and Rear, Full Nose Paint Protection Film, Husky Mud Guards, Lasfit Floor Liners, VIOFO Dash Cam
 


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:06 AM.


All Contents Copyright 2008-2024, Power Hungry Performance